Showing all 15 results
Manufacturer description Enhance your Eurorack setup with our reliable 5V adapter, designed to provide a stable 5V output for systems lacking a 5V source. Our 5V adapter is perfect for ensuring that your modules receive consistent power, whether you’re using a linear or switching power supply. Available Variants Linear 5V Adapter Voltage Regulation: Converts +12V…
A complete set to supply power to a DIY rack. It includes a 0hp power supply, DC power inlet and brick, and 2 bus boards. All the necessary accessories (cables, screws, standoffs) are included as well. The power specs are the same as the StrongPWR set. BoardPWR doesn’t have a 4hp PSU, so it saves…
If you need more than one StrongPWR or other PSU module in your synth is good to use ChainPWR cable and feed two modules by one power brick. ChainPWR is made from flexible silicone cable and from high quality connectors. ChainPWR cable made easy connection between two PSU modules. If you want to use ChainPWR,…
Manufacturer description Ensure the smooth and reliable startup of your Eurorack modules with our Soft Start Module. Designed as a compact PCB, this device provides a gentle power-on sequence for modules with high inrush currents, protecting your power supplies and bus systems from excessive stress. Key Features Soft Power-On: Gradually ramps up the power to…
These bus boards have a filtered section where you plug in your analog modules. This way, they are separated from your digital ones, which avoids interferences. There is a version with straight power connectors pointing up, and a version with angled power connectors pointing sideways. Angled power connectors take up less depth in your rack….
Manufacturer description Efficiently distribute power within your modular Eurorack synthesizer with our Flying Bus Cable with 10 of output headers. Designed for seamless integration, this cable features one 16-pin input connector and ten 16-pin output connectors, providing a reliable power solution for your modules. Key Features One 16-Pin Input Connector: Easily connects to your power…
Manufacturer description Flying bus board is a power distribution cable with low weight. Easy to install into your case without drilling or screws. One 16 pin female header and 15 pcs of 16 pin male headers. Cable length is 50cm. Perfect accessory for StrongPWR and BoardPRW PSU modules.
HammerPWR is a DIY power kit for your large racks. With 100W of power, you’re ready to power a decent sized monster case. It includes a 0hp power supply, DC power inlet and brick, and 2 bus boards. All the necessary accessories (cables, screws, standoffs) are included as well. This full set comes with 4…
HammerPWR is a DIY power kit for your large racks. With 100W of power, you’re ready to power a decent sized monster case. It includes a 0hp power supply, DC power inlet and brick, and 2 bus boards. All the necessary accessories (cables, screws, standoffs) are included as well. This lite set comes with 2…
Manufacturer description MultiplePWR cable is a low-cost solution for power distribution in eurorack modular systems. Easy to install into your case without drilling or screws. With this one you do not need ribbon power cables. Headers on MultiplePWR cable can be connected directly to modules. 16 pins input header can be connected to any PSU…
Ribbon cable 10pins – 16pins is a quality made and tested ribbon cable for powering all standard eurorack modules.
Ribbon cable 16pins – 16pins is a quality made and tested ribbon cable for powering all standard eurorack modules.
Manufacturer description PWR checker is the perfect solution for filling a 1HP space! It gives you information about all power supply rail voltages in your case. PWR Checker has 3 LEDs (+12V, -12V and +5V) on its front panel, and the module is connected to your PSU or distribution board. It is not only a…
SeventyPWR is a DIY power kit for your midsized racks. With 70W of power, you’re ready to power a small sized monster case. It includes a 0hp power supply, DC power inlet and brick, and 2 bus boards. All the necessary accessories (cables, screws, standoffs) are included as well. This set comes with 2 bus…
A complete set to supply power to a DIY rack. It includes a 4hp power supply with DC power inlet and brick, and 2 bus boards. All the necessary accessories (cables, screws, standoffs) are included as well. The power specs are the same as the BoardPWR set. This StrongPWR has a 4hp PSU, so it’s…